Hey! Are you disappointed because of your subwoofer with no sound? But you tried to fix the subwoofer. You failed because you don’t know appropriate how to fix a subwoofer with no sound. To read this article, you can set your subwoofer properly.
It can damage speakers for a variety of causes. As disappointing as it is, damaged speakers can be caused by a variety of circumstances. You may feel duped by the speaker’s limited lifespan after spending so much time finding and installing it.
You’ll need to remove your damaged subwoofer from your vehicle, repair or replace any broken parts, and connect it back together to repair it. Depending on the problem, this procedure can range from simple to challenging.
Check to see if it’s worthwhile to attempt to repair a damaged subwoofer. Determine how badly your speaker is broken and how long it will take to fix it. Check to see whether there is a cost difference between getting a new one and having it repaired.
If you’re having a problem getting your subwoofer to produce consistent sound, there are several items that you can do to attempt and fix the problem. In this article, we’ll outline some of the most common causes of subwoofer sound issues and offer advice on how to solve them.
We’ll also provide tips on ensuring that your music sounds its best when played through your subwoofer. So read on and get ready to start enjoying your music as it was meant to be.
How To Fix A Subwoofer With No Sound?
When a subwoofer is damaged, it indicates that the power is either too high or too low. Better construction allows for more errors, which means the speaker will survive longer.
Overpowering a speaker can damage the voice coil by causing it to move too far and crash on the speaker’s plate. Also, when music is playing, you may hear a buzzing sound, indicating that the subwoofer is damaged.
Overheating, ripping from erratic signals, and jamming the voice coil can all be caused by underpowering a speaker. The best amplifier is one that is rated for the RMS of your speakers.
Damage can be caused by having too little or too much power. Do not increase the volume if you hear a distorted signal or sound.
Checking For A Damaged Subwoofer
There may be some tearing or voice coil difficulties with damaged subwoofers. First, check whether a speaker stops working to see if the issue is with the speaker rather than the subwoofer. If the problem persists, It must replace the speaker.
There may be some ripping or voice coil difficulties with damaged subwoofers. Because of two factors, these are more complex problems to solve:
- Damage Coil: The voice coil is the element that receives power to assist it in pulling and pushing against the loudspeaker pole. It raises and lowers the speaker cone to make a sound in an author’s speakers.
If you’re not confident if the coil is destroyed, connect the coil’s terminals to a multimeter and see if there’s no resistance. If there isn’t, the loop is probably ruined.
- Speaker Cone Damage: It’s simple to spot a damaged speaker cone. The voice coil may be jammed or broken if the cone is inflexible and does not move. A minor rip in the foam suspension can potentially cause issues with the speakers on your subwoofer. Look for minor tears or holes with a magnifying glass.
The next step is to decide whether or not to repair a tear in the subwoofer cone or foam. It should take around 30 minutes to replace the foam, and the parts are readily available. If any cones, spiders, or voice coils are broken, they must all be replaced.
For DIY speaker repair, follow these procedures. You can also utilize materials you already have if you don’t mind certain flaws.
The steps below will show you how to fix various problems with your speaker:
Disconnection Of The Speakers
Remove the speakers from their mounting location and the connected cables with a screwdriver. After that, choose a spot to work that is both clean and well-lit.
It’s now your job to observe the speaker and determine the source of the problem. For example, is it the voice coil, the cone, or the foam suspension that is damaged?
You’ll have to place an order for the necessary components. The online market is an excellent place to go if you need foam suspension and adhesive. Try using simple speakers for the speaker cone and coil.
Fix Of Speaker Cone
If you have a subwoofer that has previously operated well, repair it using a simple patch. Because most speaker cones are constructed of paper, a simple repair with tissue paper will suffice.
If no other option is available, analyze the break and the material to see an acceptable alternative.
To cover the hole in the cone, take tissue paper and glue it in place. It’s a good idea to test the tissue paper together first to make sure it won’t shrink and damage the shape of the cone. Also, because the tissue paper is light, it shouldn’t interfere with the speaker’s operation.
You can repair a hole in a loudspeaker with tissue paper. Make sure there is glue on all tissue paper and no loose edges, as these can cause a commotion. If the underside of the cone is accessible, repeat the operation to secure the repair.
The stiffness of the loudspeaker will not be affected by using flexible glue. To ensure that it doesn’t change its performance, use the smallest glue consistent with producing a tight bond. Before you use it, make sure it’s scorched and that you’ve tested it.
Repair Of Stuck Coil
Unless the speaker cone moves, you should inspect it to see if it’s functional. If not, get a flashlight and inspect the voice coil to check if it is misaligned. Then, allow the ring to re-adjust itself by pushing the speaker up on both sides, but not too far.
Test the speaker before replacing it if you can do so without causing any damage. For example, it could be in functioning order, or some unseen damage could prevent the speaker from working.
Repair Of DIY Tear
It’s simple to repair a tear in your speaker using a paper towel and Elmer’s glue. The paper towel patch should be large enough to cover the rip but not too so, and it should not be runny. Replace a torn area with a new one if necessary.
To cover the rip, use Elmer’s glue to the paper towel patch. If desired, wait for it to dry before spray painting it black matte. With the adhesive and paper towel, this approach can assist the fibers of the torn speaker in reuniting.
Remove The Foam Surround And Replace It
How to take a speaker frame apart from its gasket when it needs to be cut out? First, scrape the glued region of the gasket with a hobby knife to remove the glue. Next, remove the gasket from the frame with a hobby knife and slide it out in one piece.
Using a hobby knife, carefully cut away the foam from the speaker. Apply alcohol to the area where the foam is fastened to the speaker using a paper towel. Scrape away any residual foam with the knife.
To repair the speaker, you’ll need glue and a new foam surround. Before you can put the adhesive into the cone, it needs to dry for one hour. Then, turn the foam over and use your finger to apply it to the speaker’s top.
Before gluing the foam to the edge, give it an hour to dry. Then, the finished result is ready for installation in the voice box.
Check the location of the speaker frame’s holes and align the gasket with them. Place the gaskets on top of the adhesive and apply glue to the top edge of the foam. Replace the speaker in the car when it has dried for an hour.
Cleaning Cone And Coils
Cut along the foam surround and around the dustcover above the terminal wires to remove the speaker cone. When cutting and cleaning the inside of the speaker, a hobby knife comes in handy. Cut the spider’s outer edge as well as the lead wires with a hobby knife.
Remove the voice coil and cover the gap where it used to be with masking tape. Using a knife, remove any other residual material from the frame, then vacuum it up again. Remove the gasket as instructed so that It can reuse it.
With a soldering iron, remove solder and wires from the speaker basket terminals. After removing the masking tape, examine the coil gap area with a flashlight. Clean if necessary.
Putting In New Components
Learn how to attach a replacement voice coil to a speaker’s frame. First, place the new lock in the gap between the two ends of the shim, making sure it is taller than the old one. Then, for an hour, press down on the glued region with a dull instrument.
How to create a speaker frame in the shape of a spider? How to apply epoxy to the inside edge of the structure, which houses the voice coil? Before putting the cone in place, make sure you remove the gasket at the end of the process.
- To smooth up the surround of the speaker:
- Use an epoxy polyvinyl treatment and a paintbrush.
- Press down on the region where the foam meets the adhesive with a dull instrument or your finger until it settles nicely.
- Remove the shim from the speaker cone if necessary.
Apply the lead wires on the cone dust cover using black adhesive. Before using speaker glue, let it dry for an hour and remove the weight. Next, apply a bead of speaker glue around the region to install the gasket on the frame nicely.
If everything goes well, you’re ready to put them in the car.
Remove And Replace The Speaker
Return the wires to the speaker and secure them. Replace the speaker in its housing using the screws that came with it when you removed it. Re-insert the speaker cover.
What Causes A Subwoofer To Stop Working?
There are a few things that can cause a subwoofer to stop working. The most common reason is if the amplifier powering the subwoofer goes out, in which case it will not be able to produce any sound. Another common issue is if something is blocking the speaker cone from hitting the walls or floor, preventing it from making a sound.
Additionally, some subs may experience short circuits due to improper wiring or excessive heat build-up over time. If you’re having trouble getting your subwoofer to produce sound, it’s worth checking these common causes first.
How To Fix A Subwoofer With No Sound
Check The Power Supply
If your subwoofer is not producing any sound, the first thing that you should try is checking the power supply to see if it’s working. If the power supply seems to be working correctly, then it’s likely that there is something else blocking the speaker cone from hitting the walls or floor. In this case, you can try removing anything that may be blocking it (like furniture) and then testing your subs again.
Verify Speaker Cone Positioning And Wiring
Another common cause of no sound from a subwoofer is if the speaker cone does not position correctly or if the wiring is defective. To check this, you can try moving the speaker cone manually and testing it to see if the sound comes out. If it does not, there may be trouble with either the speaker cone or wiring. In some cases, these problems can fix by replacing certain parts of the subwoofer’s assembly.
Check The Volume Control On Your Receiver/Controller
Many receivers and controllers have a volume control that allows you to adjust how loud your music sounds from your subwoofer. Make sure that this setting sets to the correct level, and then test your subwoofer to see if it’s producing sound. If not, you may need to adjust the volume control on your receiver/controller.
Verify The Connections Between Your Subwoofer And Receiver/Controller
If none of these solutions work, checking the connections between your subwoofer and receiver/controller may be necessary. Sometimes crossed or loose connections can cause no sound from a subwoofer. In this case, you will likely need assistance from an audio electronics expert to fix the issue.
If Nothing Works, Consider Replacing Your Subwoofer
If none of the solutions listed above work, it may be necessary to replace your subwoofer. It can be a costly repair, but if the problem is not related to a manufacturing defect or damage, it may be worth considering. If you decide to go this route, please consult an audio professional who will help you choose the best replacement for your specific needs.
Troubleshooting An Amp That Has Power But No Sound From The Subwoofer
If you have an amplifier that is displaying power but no sound from the subwoofer, there are a few possible solutions:
- Ensure the amp is correctly connected to your subwoofer and receiver/controller. In some cases, loose or crossed connections between these components can cause problems with sound production.
- Check to see if any of the speakers in your system are defective. If one or more of these speakers are not working correctly, they may be causing the noise but no power when attached to your amplifier. In this case, replacing that speaker(s ) may be necessary.
- If all of the above tests fail to produce sound from your subwoofer, it may be necessary to replace the amplifier.
If the sound from your subwoofer is intermittent or nonexistent, it may be due to a Short circuit. To test this condition, unplug the power cord from the subwoofer and receiver/controller and wait 10 seconds. If there is no noticeable sound change during this period, then you likely have a Short Circuit. If short-circuiting is detected, it will require professional repair services to correct the issue.
Final Word
Fixing a speaker cone and voice coil requires many steps, but with a bit of patience, you can do it. First, decide whether you want to spend the time fixing a speaker yourself or hire someone to do it for you. I hope now you know how to fix a subwoofer with no sound.
If you are experiencing difficulties with your subwoofer’s sound output, there may be several possible causes. If any of the steps outlined in this article do not seem to be effective in restoring sound from the speaker, it might be necessary to have the wiring checked for any problems or replace the speaker. Good luck, and thank you for reading.
Frequently Asked Question
1.How Do You Fix A Dead Subwoofer?
Ans:
- Determine the Voice Coil’s condition.
- Make sure the Speaker Cone is in good working order.
- Remove the Speaker from the Speaker Frame.
- Remove the Surround Speakers.
- Disconnect the Speaker Cone and Voice Coil.
- Replace the Voice Coil. The Voice Coil is being replaced and replacing the Speaker Frame if necessary.
2.How Do You Reset A Subwoofer?
Ans: While pushing the Input and VOL- buttons, hold down the Power button simultaneously. Release the buttons when you see RESET on the front panel display—30 seconds after unplugging the power cord.
- How Do You Fix A Speaker That Doesn’t Have Sound?
- Make sure the speaker connections are secure.
- Check the wires on the backside of your speaker and double-check that they are plugged incorrectly.
- If some of these links are loose, re-plug them to ensure that the connection is secure.
- Your speaker may not be working because of a loose connection.
3.How Long Should A Subwoofer Last?
Ans: In general, automobile subwoofers endure between 4 and 7 years. Car subwoofers are crucial for improving the sound quality of your vehicle’s audio system. Following these rules can help you extend the life of your automotive subwoofers.
4.How Can You Test If The Subwoofer Is Working?
Ans: There are a few tests that you can perform to determine if the subwoofer is working correctly:
- Check if power delivers from your amplifier to the subwoofer. In some cases, defective AC cords may cause no power flow between these components.
- Listen for sound coming from the woofer itself. If there is no sound output from your speaker. It may be need to replace. So it is to fix any problems with its audio output.
- Try using an external source of sound (such as a CD player) and connect it directly to one of the speaker terminals on the subwoofer.
If the sound from this external source is louder than the sound that comes from your speaker. Then it may be time to replace your subwoofer.
5.If The Subwoofer Does Not Produce Sound, What Could Be The Cause?
Ans: There are several potential reasons for no sound coming from your subwoofer:
- There may be an issue with the connection between the woofer and the amplifier. In some cases, loose or crossed ties can prevent power from being delivered to the speaker system.
- If one or more of the speakers in your method are not working truly. They may be causing the noise but no power when attached to your amplifier.
- If all of the above tests fail to produce sound from your subwoofer. So it may need to recover the amplifier.
6.Could A Damaged Cable Be Causing The Issue?
Ans: A damaged cable can be a significant cause of no sound coming from your subwoofer. If the connection between the woofer and amplifier is loose or faulty. This may cause power to not flow to the speaker system. Additionally, if one or more of your speakers are not working correctly. They may also contribute noise but no power when attached to your amplifier. In these cases, it may be necessary to replace. Then the entire cable assembly for sound output from your subwoofer to resume.
7.Is It Possible That The Amplifier Needs To Be Replaced?
Ans: If all of the tests listed above fail to produce sound from your subwoofer. It may be necessary to replace the amplifier. In some cases, loose or crossed connections between the woofer and the amplifier can prevent power from being delivered. Additionally, if one or more of your speakers are not working correctly.
They may also contribute to noise. But no power when attached to your amplifier. If this is the case, it may need to recover those speakers for sound output from the subwoofer to resume.
8.What Could Be Causing Excessive Noise Coming From The Speaker Enclosure?
Ans: Assuming that all of the other tests have ruled out any potential causes for no sound coming from your subwoofer. It may be necessary to inspect the speaker enclosure itself. If excessive noise emits within the section, there may be a problem with the speakers or their mounting mechanism. In some cases, this issue can correct by replacing either the speakers or their mounting bracket.
9.Could There Be A Problem With The Internal Wiring Of The Subwoofer Itself?
Ans: If no sound is coming from the subwoofer even after following all of the above steps. It may be necessary to have the wiring examined and repaired if there are any problems. In some cases, damage or moisture accumulation can cause shielding material to fail, preventing power from reaching your woofers. So if this is the case, a new wiring harness will need to be installed for sound output from your subwoofer to resume.
10.Are Any Of The Connections On The Subwoofer Adequately Tightened?
Ans: For sound to originate from your subwoofer, all connections between it and your amplifier must be tightened appropriately. If there is any slack or excessive movement in these connections. Power will not be delivered to the woofers, and you will hear no sound from them. In some cases, this issue can correct by re-tightening those connections or replacing the woofer if necessary.
11.Might There Be Something Blocking Air From Reaching The Speaker Drivers?
Ans: If you are experiencing no sound coming from your subwoofer, it may indicate that something prevents air from reaching the speaker drivers. It could be because of a blockage in the enclosure or improper placement of the speakers. If this is the case, a professional technician will need to inspect and replace any components blocking airflow.