Braided cable is the latest addition to the world of cabled devices. Almost all electronic devices use some kind of cable. Either the device is connected with a cable directly or these devices are associated with some other devices which has is wired. In both ways it is impossible to get away from cables. So, how to straighten braided cables?
From the beginning, cables are made with rubber material. But nowadays, you will see cables that has a braided pattern on it. These are called braided cable. Braided cable has gained mass popularity since it was introduced.
But like any other cable, the common problem with braided cable is that it easily gets tangled. When a wire or cable gets tangled, you will need to straighten it to use it properly. Here you will find the easy methods which will show you how to easily straighten braided cables.
What Is Braided Cable?
We all know what cables are, right! But the question comes in mind that what exactly is a braided cable. You might have heard of braided hair. But how can a cable be braided? Let us break your confusion.
A braided is basically just like a regular cable with the outer area of the cable coated with a protective material which has a braided pattern. A cable is normally made with copper, rubber and plastic material.
The main part is the copper that carries the electricity. Then the cable is covered with a rubber material. This protects the copper wire from outside environment.
In braided cable the rubber that covers the copper is again covered with another material. This material can be fabric or some kind of hybrid plastic. The fabric is then given a braided like pattern. Then the cable is known as braided cable.
Why Use Braided Cable?
The cables which are braided brings various benefits to the table. Users prefer braided cable over regular cable for various reasons. Some of the advantages of braided cable are listed below.
- Flexibility: Braided cables are way more flexible than any other cables. Regular rubber wires are not very flexible. Let’s compare a mouse with braided and unbraided cables. If you are a gamer then you will need to move your mouse very rapidly. But if the cable of the mouse is made of wire, the cable will not be flexible at all and your mouse movement will be slowed down. But if the cable is braided, the increase of flexibility will increase the mouse movement drastically. This is definitely affecting the gaming experience of the user.
- Wire Protection: Braided cables tend to have a two layer of protection. Whereas as regular cable has only one layer of rubber coating, a braided cable will often feature two layers of coating with rubber and fabric. This will provide better protection for the copper wire. Normally copper wire carries electric signal. If the surface of the cable gets broken then the copper wire might get interrupted and stop working. So braided cable is a better option to ensure further safety for the copper wire.
- Electromagnetic Protection: As all wire carries electric signal, they are prone to any type of external electromagnetic signal. If an external electromagnetic wave hits the copper wire, it may destroy the data or signal the copper wire was carrying initially. A braided cable ensures safety from electromagnetic wave and keeps the signal uninterrupted. Braided cable provides an electrostatic shield that does not let external signals to pass through.
- Longevity: Braided cables are more durable than regular rubber or plastic cables. So braided cable generally lasts a very long time. It is a great option for rough use. If you buy a rubber cable and a braided cable at the same time, you will see that the rubber cable will outlast the rubber cable by a long period of time.
The Problems With Braided Cable
Braided cable is a massive game changer in the market and we all know that. Be like all things, there are some disadvantages to using a braided cable too. Braided cables tend to be on the heavier side of cables. As braided cables has more materials for increased protection, they are heavier than rubber cables.
This causes a significant problem for some users of this particular cable. Braided cable has more weights and it causes drag to the users. Sometimes a braided cable is overkill for regular use. If you are wiring a simple light or similar device, then you don’t actually need braided cable.
Braided cable is also more expensive than regular cables. So, if you need a long length of wire, then your budget will take a big hit if you are looking for braided cable. Braided cables also occupy more space than regular cable. All the extra protection that a braided cable provides comes with these extra costs.
How To Straighten Braided Cables?
There are a couple of methods that house can follow to fix your tangled braided cable. These methods will quickly straighten the cables in just under ten to fifteen minutes.
Method 1: Using A Glass with Hot Water
- For this method you will first have to take big glass and fill it with boiling hot water. Make sure the glass can withstand the temperature of the water.
- Now take your braided cable and start to wrap it around the glass.
- Make sure that you wrapped the cable very tightly and there is no loose part in the cable.
- Now keep the cable wrapped around the glass for some time.
- After couple of minutes, unwrap the cable. You will see that the cable has been straightened.
- Now cool the cable and it will be ready to used.
Method 2: Heating The Wire
- This method is more effective for braided wires that has a bigger diameter. You will need an air heater for this process. A heat gun will be very effective. You can also use a hair dryer but it will take much longer time.
- After you got yourself a heat gun. Take the braided cable and start heating the part where the cable is tangled.
- Heat the wire for a couple of minutes. Make sure you move to heat gun over the body of the cable. Do not give heat in a specific area for a long time as it may damage the wire.
- After heating the body of the braided cable, put it with your hands and straighten it.
- The cable will be straightened without any hassle if it’s heated properly.
- Now cool the cable with some cold water and the cable will be straightened permanently.
Method 3: Coiling the Cable
- For this method you have to the cable and roll it in a coiling method.
- Use your hand or arm to and wrap around the cable around it to make a coil.
- This will keep the cable straightened and the cable cannot curl up or get tangled in any way.
- This method is only applicable when the cable is straightened beforehand. It cannot be used on tangled cables. It is more of a way to keep the cable straightened.
Why Is It Important To Keep Your Wires From Twirling?
When you braid your wires, you’re creating a spiral. This spiral can cause problems if the wires become tangled together, as it will be difficult to remove them without causing further damage. The result is a twisted cable that’s hard to work with and generally looks messy. A straight wireframe allows for easy untangling and makes your cables look cleaner and neater.
1.Start with one wire and thread it through the eyelet of the other wire. Pull tightly so that the edges are close (as you can see in the diagram below). You can do this with either hand. Left-handers should hold one end of the first wire in their left hand. And they should do the same with the opposite right-hand wire. While right-handers should hold both ends of each wire once. When you’re turning them around like this. It’s important to keep your cables together then too much space between them will cause problems later
- Make a small loop with the first wire, and do the same with the second wire (see diagram below). Now take both loops and twist them around each other – this will create a smaller spiral. You can now remove the loops by pulling on them firmly or by using your fingers if you’re comfortable with it.The tighter you hold onto your wires, the smaller and more tightly wound their spirals will be when they’re finished.
- Repeat steps one and two until all of your cables are straightened – remember to keep them close together while you’re winding them up!
How To Straighten Out Your Headphone Wires?
When you have a bunch of cables that need to be stored neatly and neatly. One of the best ways to do this is to use headphone cables There are different types of headphones out there. So it can be difficult to track which wire goes where.
There are a few different ways to straighten your headphone cables. So that you can make them look clean and tidy. So that there are no obstacles or bends in them
The first method is the old-fashioned way – with your hands! You can easily grab each individual wire and gently pull/twist it until it straightens out.
Another method is to use a wire stripper. This can be a bit more difficult since you will need to cut the ends off of each headphone wire and then strip them down to the conductor.
The last method is using pliers or crimpers. You can easily clamp onto one end of the headphone wire and start gently pulling/pushing until it becomes straighter without any kinks or bends in it.
Hang The Headphones From A Stand, A Hook, Or Desk Edge
When it comes to storing your headphones. One of the best ways to keep them organized and tidy is by hanging them from a stand, a hook, or some other stationary object. This will help you easily see what wire goes where so that you can avoid getting tangled up in cables again. Store your headphones in a clothes drawer
Organize your headphone cables. And another great way to keep things tidy is to store them in the same place you keep your other clothing items. This will help you easily grab a wire when you need it.
Set The Wire Straight Using A Weight Or Flat Surface
If all of the above methods fail to get your headphone wires straighter, you can try using a weight or flat surface to set the wire straight. This will help create a more uniform shape in the wire and reduce any kinks or bends. There are a few methods that you can use to get your headphone wires straighter.
- Use a wire stripper: This can be a bit more difficult since you will need to cut the ends off of each headphone wire and then strip them down to the conductor.
- Use pliers or crimpers: You can easily clamp onto one end of the headphone wire and start gently pulling/pushing until it becomes straighter without any kinks or bends in it.
3. Hang the headphones from a stand, a hook, or desk edge: When it comes to storing your headphones, one of the best ways to keep them organized and tidy is by hanging them from a stand, a hook, or some other stationary object.
Conclusion
I hope now you know how to straighten braided cables. So, now you know how to straighten braided cables. To do this, just follow the steps we have mentioned above and start working with your new cables!
Also, notice that not all braided cables behave in the same way. As such, it is always better to use caution when handling these types of cables, especially if your job requires a high level of focus on your workstation since it can cause frustration in no time.
FAQs
1.How Do I Fix A Headphone Wire Twist?
Ans: If you have a headphone wire that has gotten twisted, the best solution is to use a hair dryer. Put the headphones on low heat and start slowly moving the hair dryer back and forth along the entire length of the wire until it becomes straighter. Be careful not to overheat or melt any wires or plastic pieces in your earphones.
Ans: There can be a few reasons why headphone wires might start to twist. One reason is if there is too much tension on the wire, which can occur if it’s caught in between two objects or isn’t being evenly distributed along its entire length. Another possible cause could be if the wire has kinks or bends in it. It will cause this distortion and twist in the wire
3.How Do I Straighten My Headphone Wires?
Ans: There are a few different ways that you can try to straighten out your headphone wires if they’ve become twisted or kinked. You can use a hair dryer, an electrician’s crimper, or pliers. Be sure to be careful not to overheat the wire and damage it in the process.
4.How Do I Fix A Twisted Headphone Wire?
Ans: If your headphone wires have become twisted, you can use a hair dryer to fix the issue. Keep the headphones on low heat. And slowly start moving the hair dryer back and forth along the entire length of the wire until it straightens. Be careful not to overheat or melt any wires or plastic pieces in your earphones.
5.Why Do I Need To Keep My Headphones Straight?
Ans: You want to keep your headphones upright. The main reason is to keep them as free from distortion and twist as possible. If the wires are twisted or twisted, the magnetic field created when you plug them into the device will cause this distortion and twist in the wire. This can affect both sound quality and how comfortable they feel while wearing them.
6.What Is Litz Wire?
Ans: Litz wire is a type of wire that’s been specifically designed to resist distortions and twists. This is why many headphone manufacturers go out of their way to use Litz wire in their products.
7.How Do I Keep My Headphone Cables Sorted?
Ans: One way to keep your headphone cables sorted is to zip-tie them together at the end of each cable. This will help keep them organized and make it easier to avoid tangles.